Structural Bolting Handbook 2016
Jetzt neu im Sortiment
EUR 24,00
∙ Kostenloser Versand
Structural Bolting Handbook 2016
Jetzt neu im Sortiment
Structural Bolting Handbook 2016
Ein Muss für:
- Stahlbauer- und Stahlhersteller
- (Stahlbau)Monteure
- Aufsichtsbehörden
- Ingenieure und Baustatiker
Diese Ausgabe 2016 des Structural Boltting Handbook basiert hauptsächlich auf der Ausgabe Juni 2014 der RCSC-Spezifikation für strukturelle Verbindungen unter Verwendung hochfester Schrauben, zitiert von der AISC-Spezifikation 2010 für Stahlkonstruktionen (AISC 360-10). Mit der AISC-Spezifikation für Stahlkonstruktionen für das Jahr 2016 (AISC 360-16), die in der RCSC-Spezifikation von 2014 nicht behandelt wird, wurden jedoch wesentliche Änderungen in Bezug auf strukturelle Verschraubungen umgesetzt:
- eine Erhöhung des STD-Bolzenlochdurchmessers und der SSL- und LSL-Schlitzbreite für Bolzen mit einem Durchmesser von 1 Zoll und darüber,
- Anerkennung der neuen Norm ASTM F3125, die ASTM A325, A325M, A490, A490M, F1852 und F2280 konsolidiert und ersetzt,
- erhöhte Mindestbolzenanforderungen für A325-Schrauben mit einem Durchmesser von 1-1 / 8 Zoll und mehr, die sich auch auf die Verifizierungstests vor der Installation auswirken, und
- Einführung neuer Schrauben der AISC Group C mit 200 ksi Zugfestigkeit, ASTM F3043 und ASTM F3111
Dieses Handbuch enthält Informationen unter Verwendung von:
- Die AISC-Spezifikation 2010 mit den RCSC-Spezifikationsbestimmungen von 2014 und
- Die AISC-Spezifikation 2016 enthält nach Möglichkeit entsprechende aktualisierte Informationen für die Verwendung, bis die RCSC-Spezifikation aktualisiert wird.
This 2016 edition of the Structural Bolting Handbook is based principally upon the June 2014 edition of the RCSC Specification for Structural Joints Using High-Strength Bolts, cited by the 2010 AISC Specification for Structural Steel Buildings (AISC 360-10). However, significant changes regarding structural bolting were implemented by the 2016 AISC Specification for Structural Steel Buildings (AISC 360-16) that are not addressed by the 2014 RCSC Specification, including:
- an increase in STD bolt hole diameter and SSL and LSL slot width for bolts 1 inch diameter and above,
- recognition of the new ASTM F3125 standard, which consolidates and replaces ASTM A325, A325M, A490, A490M, F1852 and F2280,
- increased minimum bolt pretensions for A325 bolts of 1-1/8 inch diameter and greater, which also affects pre-installation verification testing, and
- introduction of new AISC Group C bolts with 200 ksi tensile strength, ASTM F3043 and ASTM F3111
This Handbook has included information using both:
- the 2010 AISC Specification with 2014 RCSC Specification provisions, and
- the 2016 AISC Specification provisions with appropriate updated information, where possible, for use until such time as the RCSC Specification is updated.
A must for:
- fabricators and erectors
- ironworkers and fitters
- inspectors
- engineers and detailers
4″ by 8″ pocket-sized convenience, 144 pages
- Step-by-step instructions for performing bolt installation using RCSC turn-of-the-nut, calibrated wrench, twist-off bolt and direct tension indicator methods
- Step-by-step instructions for performing bolt installation of new 200 ksi ASTM F3043 and F3111 Grade 2 assemblies, ASTM F3148 TnA144 assemblies, and Squirter® DTIs
- Step-by-step pre-installation tests for each method
- Step-by-step inspection procedures for each method
- Step-by-step arbitration of disputes procedure
- AASHTO / FHWA rotational capacity test procedures
- Bolted joint descriptions
- Snug-tight joint acceptance criteria
- Bolt, nut and washer product identification markings
- Manufacturer mark and source information
- Torque estimation tables
- Installation wrench selection tables
- Bolt length tables
Rabatte bei Sammelbestellungen
ab 10 Exemplare = 5,00 %
ab 50 Exemplare = 10,00 %
ab 100 Exemplare = 15,00 %
ab 250 Exemplare = 20,00 %
Kunden kauften auch